Polished Mid Independent Skateboard Trucks
New Independent MiD trucks feature a lower profile hanger for optimal contact point angle on your nose and tail for flip tricks, ledges, and all-around street skating with a recommended wheel size of 53mm and under.
The newly designed and first ever Independent inverted kingpin can be used with either a 5.5mm Allen key or standard 9/16" hex wrench. The innovative new Shaft Nut in the baseplate creates a rigid and durable solution to lateral movement found in most inverted kingpin designs and increases adjustability.
The new MiD is 52mm tall and built on Independentճ legendary geometry with full size cushions for maximum turning action and comes in 129, 139, 144, 149, 159 sizes.
The all new design includes a new baseplate stamp and size designations underneath the hanger for easy identification.
356 Aluminum hanger and baseplate
4140 Chromoly steel axle
Inverted Grade 8 kingpin w/ 9/16" & 5.5mm Allen
Steel Shaft Nut with nylon locking insert
What Size Trucks Do I Need For My Board?
|6.65 - 7.15||6.9 in||109||-||110|
|7.35 - 7.85||7.6 in||129||7.6||130|
|7.75 - 8.25||8.0 in||139||8||140|
|8.00 - 8.50||8.25 in||144||8.25||-|
|8.25 - 8.75||8.5 in||149||8.5||150|
|8.50 - 10.40||8.75 in||159||-||-|
|8.75 - 10.40||9.0 in||-||9.0||-|
|8.88 - 10.40||9.125 in||169||-||-|
*Deck range recommendation varies depending on type and width of wheels
Do I Need Riser Pads?
When running certain combinations of trucks and wheels sometimes it becomes necessary to use riser pads to avoid 'wheel bite'. Don’t know what 'wheel bite' is? Well consider yourself lucky. Wheel bite is what happens when you turn your board and your wheel touches the deck. If you do this hard enough the wheel will 'bite' and stop rolling. This often means that you go flying off your board. So if you're running bigger wheels make sure to read through this chart. While it might look like homework it's definitely more fun than hitting the pavement!
|Truck Height**||Wheel Range***|
|48.5 - 52||49 - 53|
|52 - 53.5||51 - 55|
|53.5 - 55||53 - 57|
|60||55 - 59|
If you are ordering risers for your complete, please make sure you have chosen hardware that accommodates the height of your risers. 1¼" hardware will work with ⅛” risers and 1½” is needed for ¼” risers.
**You can find truck height information in the 'Details' area a specific truck page.
***Wheel size recommendation with no riser.
What Size Hardware Do I Need For My Board?
When attaching your trucks to your board you’re gonna want to make sure your bolts are long enough. If you use risers, you’ll want to run a longer bolt, but you don’t want to go too long or your setup will look all goofy! Use the chart below and everything will fall into place.
|Wheel Size||Riser Size||Hardware Size|
|7 ply deck||9 ply deck|
|49 - 55||-||7/8"||-|
|55 - 58||1/8"||1"||-|
|57 - 60||1/8" - 3/8"||1 1/4"||1 1/4"|
|60 - 65||3/8" - 1/2"||1 1/2"||1 1/2"|
139 - 8.00 in
144 - 8.25 in
149 - 8.50 in
159 - 8.75 in
139 - 137 mm
144 - 144 mm
149 - 149 mm
159 - 156 mm
139 - 392
144 - 402
149 - 409
159 - 412
No Reviews Yet | Add Your Review